The etrailer hub and drum assembly # AKHD-545-35-K is compatible with your ALKO axle. It is compatible with just about anything including ALKO but also Dexter and Lippert. These 3 companies (technically 2 since Dexter bought that division of ALKO) make up the majority of trailer axles in the industry. view full answer...
For your 2016 Keystone Hideout 175LHS, I recommend the over-under conversion kit # K71-384-00 which will put your axles under your leaf springs and raise your trailer by the diameter of the axle plus the height of the leaf spring stack. This also will not require upgrading any other components but you can choose to upgrade tires or wheels if desired based on that additional clearance. view full answer...
Power runs to the backup camera part # FOS05TASF when the trailer is put in reverse. There is a switch in your reverse wiring that trips the camera to turn on. You do have to be plugged into the 7-way on your towed vehicle. view full answer...
There isn't a master key that unlocks the Global Link RV Entry Door Locking Latch Kit # 295-000019. Only the key that comes with it will unlock it. Which if you need to order more of these all keyed the same just select "keyed alike from the drop down menu and all of the ones we'll ship you will be keyed the same. view full answer...
The Adco RV Cover for Travel Trailers - All-Climate + Wind (DISCONTINUED) AD77ZR will fit travel trailers between 24 feet 1 inch and 26 feet long. The cover doesn't vary by different models like you listed only changes by length of trailer. This is a great product yet not the correct fit for your trailers listed.
The 2018 Keystone Bullet 243BHS has a length of 28.33 feet, the 243BHSWE has a length of 27 feet 10 inches, and the 247BHSWE has a length of 28.25 feet, so the correct fit is... view full answer...
I do have a solution for you but we do not have an axle that meets the measurements you have provided. What I recommend to replace the axle AND the suspension all at once is a Timbren Axle-Less system such as # A35RS545 or # A35RS545E. With this set up you would not need to replace suspension parts and the Timbren springs that will replace them do not require maintenance like leaf springs set up would. I have linked a video example of a Timbren system.
There are a lot of things that go... view full answer...
The etrailer 6,000-Watt Portable Inverter Generators part # 333-0003-2-0007 should be enough to power the 13.5k btu and 15K btu air conditioning units on your travel trailer. They have a 6,000 watt starting output and a 5,500 watt running output.
The average RV 13.5K btu air conditioning unit pulls 2,750 watts while starting and 1,250 watts while running. The average RV 15K btu air conditioning unit pulls 3,500 watts while starting and 1,500 watts while running. Therefore, so long as... view full answer...
Yes, the trailer wheel part # AM22323HWTB that you referenced will fit your 2017 Keystone Bullet 272 BHS. Then for an ST205/75R14 to use with it the part # AM10235 would work great. We don't have a version of this mounted already though so you would have to mount the tire locally. view full answer...
Sounds like you are just looking for a wet bolt kit for your 2018 Keystone Bullet 269RLS. For that we have the wet bolt part # 126B2 for a single wet bolt and nut. Or for a kit that includes wet bolts, new bushings, heavy duty shackles, and nuts for a tandem axle you'd want the part # MR46ZR and you'd be set. view full answer...
The # 288-07432-2 loading ramp would be an excellent choice for loading a self-propelled snowblower into the bed of your Silverado. The rungs on the ramps will provide excellent traction for both the tires on the snowblower, and for the person loading it.
If you click the provided link, you can see a demonstration video featuring the ramps. view full answer...
I looked up your Keystone Bullet 220RBI and it's a camper on an A-frame trailer which we have a great powered jack option for.
I recommend the Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift # JET-5000.
It has a lifting capacity of 5,000 lbs which would be more than you'd need but will ensure that the jack will operate quickly and last a long time. view full answer...
The MORryde 14-3/4" Shock Absorbing Equalizers # MR34AR will allow you to upgrade your factory equalizers. These are specifically designed to fit with the 42" axle center spread you have on your Bullet. I recommend also changing out for the Wet Bolt Kit # MR46ZR which will allow the suspension to more easily move throughout its range.
I was able to find your 2018 Keystone Bullet 277BHSWE has 3,500lb axle but I could not get an exact part number for the replacement leaf springs. I have... view full answer...
The triple step Lippert Solidstep you want is the part # LC698799 as this step has a width range of 24" - 26" wide for the doorway which is perfect for what you have. view full answer...
Ultra-Fab 2" Trailer Hitch Receiver # UF35-946403 is a general-purpose weld-on hitch that will fit I-beam, C-channel or rectangular trailer frames from 47- to 77-inches in width. It is not specific to any brand or series of trailer, such as your 2014 Keystone Bullet 247BHS, so to see if it is a suitable fit you'll want to measure the trailer frame rails to make sure their spacing falls into the range noted above.
This hitch is intended only for use with hitch-mount accessories such as... view full answer...
The 10" x 1-1/2" braking assemblies part # K23-472-473-00 will use the same four bolt brake mounting flange as the 10" x 1-3/4" braking assemblies you have but the hub/drum that goes with these uses a LM67048 inner bearing and L44649 outer bearing which I don't believe is correct for your trailer.
The most common replacement for the 10" x 1-3/4" braking assemblies you have are going to be the 10" x 2-1/4" braking assemblies, part # 23-26-27. The correct hub/drum for this is part # AKHD-545-35-K... view full answer...
Your Atwood GC6AA-10E Water Heater does not require an anode rod so you will be able to use the Drain Valve # CAM11703. You do not need the Anode Rod w/ Drain # CAM11533 which you found. view full answer...
Trailer manufacturers do not typically keep record of smaller parts such as the scissor jacks that would have come with your 2016 Keystone Springdale Summerland Mini 17. With that being said, just about any properly rated scissor jack will work great as a replacement.
The Lippert Scissor Stabilizer Jacks w/ Handle # LC285326 referenced in your question have a total lift capacity of 10,000 pounds (5,000 pounds per jack). They have a collapsed height of 4-1/4 inches and a height of 24 inches... view full answer...
If you wanted to level your trailer from front to back and side to side you'd only need one of the Hopkins Electronic LED Smart Levels # HM08201.
The hinged design of this kit allows you to check the front to back and side to side level just be swiveling it. view full answer...
According to what I was able to find your 2020 Keystone Bullet 291RLS has a coupler designed for a 2-5/16 inch hitch ball so for hitch ball that works with your WD system and is right size you'd want the part # 63847. view full answer...
The actual weight of the Lippert Components High-Speed Power Stabilizer Jack # LC298707 not including the switch is 64 lbs. I've attached the instructions for installation to assist with installation on your 2018 Keystone Bullet Ultra Lite Trailer. view full answer...